EP 61: Good Better Best Hunting Arrow Builds for Every Scenario

EP 61: Good Better Best Hunting Arrow Builds For Every Scenario
EP 61 — Good Better Best Hunting Arrow Builds for Every Scenario
The Archery Project Podcast
Episode 61  ·  Hosted by Zakk Plocica
Est. reading time — 15 minutes

Season is close, so Zakk takes two years of arrow ballistics data and turns it into actual builds. Four honest questions about your hunting, three component decisions in the right order, then good/better/best arrow builds for the whitetail timber hunter, the Western hunter, and the fixed-blade purist — plus the six rules that apply to every arrow you’ll ever build, regardless of budget.

Listen to the full episode on Apple Podcasts, Spotify, YouTube or stream below.

We discuss:

Timestamps refer to the audio/video episode above.

  • Why most bowhunters build arrows backwards — and the order that fixes it
  • Question 1: what you’re hunting and the distances you actually shoot
  • Question 2: mechanical or fixed blade, and the 2″ / 4″ / 6.5″ group numbers behind it
  • Question 3: an honest assessment of your shooting under pressure
  • Question 4: how much arrow noise matters, and why a quiet vane alone won’t save you
  • The three decisions in order: broadhead, then vane, then shaft and FOC
  • The broadhead hierarchy: SEVR, Grim Reaper Fatal Steel, Jekyll, Toulou, Iron Will
  • Vane selection by broadhead type — Talon, Hybrid HP, DCA Super Sabre, FFP 360
  • Four-fletch math, stiffer vane material over 310 fps, 4mm vs 5mm, and spine
  • FOC: three smart ways to raise it, and the one thing not to do
  • Builds for the whitetail hunter in thick timber
  • Builds for the Western hunter in open country
  • The fixed-blade purist build
  • Zakk’s own 2026 build, component by component
  • Six rules that apply to every arrow build, every budget

00:00Why Your Arrow Build Needs a Framework, Not a Shopping List

Hunting season is close, and that has Zakk back on arrows. The last two episodes covered the data itself — breaking down the 2026 Arrow Ballistics Study and then how to build hunting arrows using it. This one is the practical end of that arc: specific scenarios, and how he’d build an arrow for each of them using the data rather than habit.

He opens with a question worth sitting with for a second.

“When was the last time that you actually thought about why you built your arrow the way you built it?” — Zakk Plocica

Not grabbing a shaft off the shelf. Not taking somebody’s word for it. Actually thinking through the logic of the build — broadhead first, then vane, then shaft, then FOC, in that order, for a specific reason. Zakk’s take is that most bowhunters don’t do that, and he puts himself in that group. His own pattern has been to pick an arrow for the year, then treat the broadhead and vane as afterthoughts. He says plainly he has not been as data-driven as he probably should be.

The usual version of this is picking a broadhead based on what killed something last season, grabbing whatever vane the shop has in stock, and calling it done — then wondering why the setup isn’t as consistent or accurate as you’d like. The goal of this episode is to replace that with a framework.

The source material is two years of the most rigorous arrow testing that’s been done for bowhunters: the 2025 and 2026 studies combined. James Yates led the work, with Precision Cut Archery, Easton, and Hoyt involved for 2026, plus an independent acoustics lab running Doppler radar chronographs. There were roughly 1,500 shots in 2025, and a regression analysis across 34 different arrow builds for the FOC section alone. Zakk went through both years — the articles, the videos, the published results — and this episode is his interpretation of all of it.

What he’s explicitly not doing here is re-teaching the physics. You don’t need to understand static margin or center of pressure to build a better arrow. You need a framework and a parts list. So: four questions about yourself, three decisions in the right order, builds for different scenarios, and six rules that apply to all of them.

05:47Question 1: What Are You Hunting, and at What Distance?

Before a single product name gets mentioned, four questions — answered honestly, about the season you actually have, not the one you picture.

A whitetail hunter sitting a tree stand in tight timber inside 25 yards has a completely different set of priorities than someone chasing mule deer in open country at 60-plus. The timber hunter should prioritize a quiet arrow and penetration. Trajectory is close to irrelevant at 25 yards — you’re obviously not shooting a thousand-grain arrow, but at that distance it shouldn’t be the thing driving the build.

For the Western hunter, trajectory is the whole game, because the number one cause of misses in the open is ranging error.

“If you have a flat shooting arrow, being off two yards because you have a range estimate error is not going to be that big of a deal. But if you have an arrow that is arcing like a dang rainbow, two yards can be the difference between a wounded animal or a complete miss.” — Zakk Plocica

Zakk paraphrases Yates from the 2025 video on this: misjudge a 70-yard shot by two yards with a flat-shooting arrow and those two yards may not push you outside the kill zone. That’s what flat trajectory actually buys you — range forgiveness.

So answer it honestly. Inside 30 to 35 yards, trajectory isn’t priority one; quiet and penetration are. Out West, trajectory outranks almost everything, because the cost of a misranged animal with a rainbow arrow is much higher.

08:15Question 2: Are You Shooting Mechanical or Fixed Blade?

This is the debated one, and Zakk anchors it to what he calls the most important number in the episode. The 2025 study used a pneumatic shooting machine — no human error, no torque, perfectly consistent every shot, which humans are not — and shot every broadhead from a tuned bow at 70 yards.

Tested at 70 yards (2025, shooting machine) Average group
Field tips 2 inches
Mechanical broadheads 4 inches
Fixed blade broadheads 6.5 to 7 inches

That gap isn’t a tuning problem — it’s physics. A fixed blade has more drag, creates more lift at the front of the arrow for the vane to overcome, and is less aerodynamically forgiving than a mechanical. The study confirmed it for the second year running. Zakk is careful here: this isn’t a knock on fixed blades, and there are good reasons to shoot them, but you have to understand the flight penalty you’re accepting, because it changes your vane selection downstream.

“Your broadhead choice is your vane requirement. Decide this first. Everything else follows.” — Zakk Plocica

09:49Question 3: How Honest Are You About Your Shooting Under Pressure?

This is the question Zakk thinks most of us overestimate, himself included. Not how you shoot at the range — how you shoot when the buck or the bull of a lifetime steps out at an awkward angle, your heart rate is up, and you’ve got a narrow window before he winds you. Do you rush the shot? Pull it? Occasionally shank one in the heat of the moment?

His own answer is that he isn’t the greatest shooter in the world, he spends a lot of time with his bow and is comfortable with it, but he knows that when the moment comes he wants forgiveness — so that’s what he builds around, in the bow and in the arrow.

“If you can’t really hold your stuff together in the heat of the moment, you’re going to want to have more vane on the back of your arrow.” — Zakk Plocica, quoting James Yates from the 2025 video

The practical split: a disciplined shooter with consistent form can optimize for drag efficiency and run less vane. If you know you rush it, you need more lift recovery — more vane — to compensate for the angular error you induce at the shot. There’s no upside to lying to yourself about which one you are. The goal is a successful hunt and a successful recovery, and if that means more vane or running a mechanical, then set the ego aside, look at the data, and see what makes the most sense for you.

12:40Question 4: How Much Does Arrow Noise Actually Matter for You?

The 2026 study tested every broadhead and vane combination for noise through an independent acoustics lab, weighted for how a deer hears — about an octave higher than humans. The spread from the quietest broadhead to the loudest was roughly 15 decibels, which on a logarithmic scale is roughly three times louder. The spread from quietest vane to loudest was about 10 decibels, or twice as loud.

The part people push back on is which one matters, and the study’s answer is both. A quiet vane paired with a loud broadhead is not a quiet arrow. A loud vane paired with a quiet broadhead isn’t either. You have to engineer the whole system.

How much you should care depends on your answer to question one. For a Western hunter at distance, a deer’s reaction time matters less — even if it jumps the string, the arrow is already there. But in tight timber at 25 yards, on pressured public land, on skittish deer like the ones in eastern North Carolina, it’s a very real consideration.

Zakk’s framing of why the arrow specifically matters: the bow makes one short, non-continuous crack, like stepping on a stick in the woods — one and done. The arrow makes a continuous hissing sound tracking toward the animal, and their instinct is to react to an approaching threat. The data now backs that up. Ideally you quiet both, but if he had to prioritize one, he’d take the quiet arrow over the quiet bow.

15:01The Order That Matters: Broadhead, Then Vane, Then Shaft and FOC

With the four questions answered, the components come next — and Zakk thinks most hunters do this backwards. The right order is broadhead first, then vane, then shaft and FOC, because each decision constrains the next.

  • The broadhead you choose determines how much lift recovery you need from your vane.
  • The vane you choose affects how much weight budget you have left for FOC.
  • The shaft you choose affects your dynamic spine — and its GPI sets how easily you can move the balance point forward. A higher-GPI shaft fights you on FOC; a lower-GPI shaft lets you add front weight without driving total arrow weight through the roof.

It’s a system, and it gets built in that order.

16:17Decision One: The Broadhead Hierarchy After Two Years of Data

Mechanicals

Across both study years, the mechanical hierarchy is clear. The SEVR family — the 2.0, the 1.5, and the 1.5 Hybrid — are the most consistently validated mechanicals in the data, and Zakk says you can’t deny what they’ve done. The SEVR 2.0 won the 2025 accuracy crown, shooting field-tip-equivalent groups from the machine. The 1.5 and 1.5 Hybrid dominated the 2026 high-speed testing at 325 feet per second and came in as the quietest mechanicals tested, rivaling the quietest fixed blades.

He also likes the system around them: you can buy them individually, the newest versions no longer require collars, and the lock-closed set screw means you can practice and test with the same head you hunt with. He’s open that he wishes the shop could carry them.

Beyond SEVR, three more mechanicals earned their place. The Thorn Rift 2.2 and the Beast Titanium were the most aerodynamic heads tested in 2025 and tied for lowest drag of any broadhead in the test. The Grim Reaper Fatal Steel was, in Zakk’s view, the biggest accuracy surprise of 2026 — it grouped with field points at 290 feet per second, and he expects it to be a popular head this season.

Fixed blades

On the fixed blade side, the Evolution Jekyll was the best-flying head of 2025 — three-inch groups, twice, from the shooting machine, with nothing else close. The next best were the Slick Trick Standard four-blade and the Grim Reaper Micro Hades at roughly five and a half to six inches. The Toulou was the quietest fixed blade in the 2026 combo noise testing, showing up as part of the quietest arrow combination tested overall. And the 100-grain Iron Will Solid surprised everyone in 2026 by competing with several mechanicals on drag — not what you’d expect from a fixed blade.

Before you blame the broadhead

Zakk stops the product talk here for what he calls a rant, and it’s the most practically useful minute in the section.

“Broadhead flight problems are almost always a tuning problem within the bow.” — Zakk Plocica

They see it every week as season approaches. If your broadheads aren’t flying, tune the bow before you change anything else. Start with paper tuning. You can’t swap heads back to back without retuning in between — you have to retune after every change you make. Skip that step and you’ll never have a setup that performs downrange, especially as distance opens up. And the point of testing with your own equipment isn’t just accuracy, it’s confidence: the moment you start questioning your setup, your shooting gets worse. That’s the argument for shooting year-round.

16:37Decision Two: The Vane Your Broadhead Demands

Once the broadhead is settled, you know how much lift recovery you need — and the vane choice follows from that, not from what’s in the bin at the shop.

Shooting fixed blades? You need maximum lift recovery, and the data-backed picks are the AAE Talon and the Hybrid HP. The Talon won the lift recovery category in both 2025 and 2026, drifting 6.3 inches less than the average at 70 yards — a genuinely meaningful number. The Hybrid HP was right behind it and actually edged it out slightly at higher speeds, at about 18 grains of total vane weight, the best weight-to-steering ratio in the study. Less vane weight means more weight budget left for FOC.

Shooting mechanicals? The DCA Super Sabre is the two-year confirmed answer for the best overall blend, and Zakk notes the shop has seen a big uptick in sales on them for good reason. Top three in the 2025 drag/lift scatter, confirmed again in 2026, and on two years of data it’s the most versatile hunting vane in the study. The TAC Driver 2.25 — another one he’s fond of — and the Flex Fletch Silent Night 2″ were also in that 2025 top-three cluster.

Prioritizing quiet? The Flex Fletch FFP 360 was the quietest vane tested in both 2025 and 2026. Yates has been shooting it for ten years specifically because it’s the quietest vane he’s ever found, and the study confirmed it again — it’s quieter than vanes half its size, thanks to the gradual profile. The FFP 300 is nearly identical on noise, slightly behind the UV vane, which debuted in 2026 and landed in the top three for quiet immediately.

The four-fletch question

The 2025 study measured this precisely. A four-fletch costs roughly 7.3% more drag but buys 3.8% better steering — about 0.9 inches less broadhead drift at 70 yards — and adds less than one decibel of noise. Zakk’s read: for fixed blade shooters that trade is absolutely worth it. For mechanical shooters, he’s not convinced it is.

24:18Vane Material, Shaft Diameter, and Spine

Over 310 fps, go stiffer on vane material. The 2026 high-speed data is definitive. A lot of this year’s bows — the Mathews ARC, the PSE Sicario — are putting up big speeds even with a sensible 440 to 460 grain arrow. If yours is one of them, you want a stiffer vane like the Flex Fletch 360X steering the back of that arrow.

4mm shafts have exactly 10% less drag than 5mm on an equivalent build, confirmed in 2025. That’s not nothing — at 70 and 80 yards it translates into real inches of wind drift and elevation drop. If your hunting application allows it, the smaller diameter is worth it, which mostly means Western and long-distance shooters rather than the guy hunting 25 yards in the whitetail woods.

On spine, stiffer kept winning. The 2026 study tested every spine from 200 to 340 on modern bows — the Hoyt with the XTS tuning system in particular — and going 100 nominal spine stiffer, say a 300 to a 200, predicts about 0.9 inches tighter mean radius on your broadhead group at 70 yards. There was no sweet spot and no point where accuracy reversed. Stiffer was better all the way through the tested range.

But this is exactly where Zakk pumps the brakes. The recommendation is an optimally tuned, slightly stiffer dynamic spine, especially when shooting broadheads — and the study itself cautions against going excessively stiff, because it adds mass, which costs you speed and trajectory forgiveness.

“We can’t go from one extreme to the next, or you’re going to lose somewhere. We want to optimize for what we’re doing.” — Zakk Plocica

27:15FOC: What the Regression Actually Found

The 2026 study ran 34 arrow builds through a regression analysis specifically to isolate the effect of FOC. The result: increasing FOC by five percentage points — say 13% to 18% — predicts about a two-inch reduction in broadhead group mean radius at 70 yards, which is four inches on total group diameter. And there was no ceiling. Accuracy kept improving across the entire tested range, from 10% all the way to 25% FOC.

The limit isn’t accuracy degrading, it’s your dynamic spine tolerance and your trajectory goals. Load up enough point weight and total arrow weight climbs, the arc gets steeper, and you give back the range forgiveness you were chasing in question one.

Three smart ways to raise FOC

  • Cut the arrow shorter. Moves the balance point forward and stiffens dynamic spine at the same time — two wins from one change.
  • Drop to a lower-GPI shaft and redirect the savings forward, internally, via insert weight rather than out front. This is the direction Zakk is going himself. The tradeoff is durability: lower GPI generally means a less bombproof shaft.
  • Use lighter vanes and move those grains to the insert.

What you don’t want to do is simply stack more tip weight onto your current arrow. With FOC held constant in the model, less total point weight actually improved groups by about 0.7 inches. Zakk is candid that this one is counterintuitive and that parts of the regression were over his head — he’s relaying what the data says, not claiming to have derived it.

29:53Build One: The Whitetail Hunter in Thick Timber

Tree stand, ground blind, or saddle. Tight cover, pressured deer, everything inside 35 or 40 yards — Zakk’s own situation for most of the season. Noise matters, penetration matters, trajectory is not the defining factor. Every component below has a data point behind it, and he’s clear these are examples rather than the only right answers.

Good

An Easton Axis 5mm — the most durable shaft on the market, and in his words a machine of a whitetail arrow. Cut it short. With a stock insert and the collar, his came out somewhere between 11 and 13% FOC. Nothing exotic; the arrow just performs. AAE Max Stealth on the back in a three-fletch, two degree right helical — his go-to for years — or the factory-fletched AAE Hybrid, which is the equivalent. Pair it with a SEVR 2.0, the best-grouping mechanical of 2025 at field-tip-equivalent groups from the machine. Pick the spine off your draw weight and draw length, use stock components, and don’t overthink it. A 2″ cutting diameter on a whitetail is plenty.

Better

Step up to the Easton FMJ Max — nearly identical GPI to the Axis 5mm, but it’s Easton’s lower-GPI FMJ with a carbon interior and aluminum exterior, so penetration is better and it pulls out of targets easily. Cut it as short as you can to raise FOC, trim weight, and stiffen it up. The difference from the good build is where the weight goes: rather than an outsert system, use Easton’s HIT insert internally. They offer a 50 or 75 grain stainless option, and you can break it off and add another 50 grains up front. Same vanes, same SEVR 2.0. Total weight goes up slightly, which doesn’t matter here because trajectory isn’t priority one, and you get more FOC and a harder-hitting arrow.

Better still

Run that same build in a four-fletch, two degree right helical, paired with the Flex Fletch FFP 300 — an incredibly quiet arrow that also steers extremely well. Zakk’s honest caveat is that the steering may be overkill for this application; personally he’d probably still run it in a three-fletch with the Max Stealth.

Between the two shafts: if durability is priority one, the Axis 5mm. If you want a bit more penetration, the FMJ Max with internal weight added. He likes 5mm here specifically because of how much weight you can add internally, the range of component options, and the fact that components are more affordable.

34:54Build Two: The Western Hunter in Open Country

Mule deer and elk, open country, shots from 40 to 80-plus yards. Ranging error is the number one cause of misses out there, so flat trajectory and range forgiveness are non-negotiable, and wind is a real factor.

Good

The Easton 5.0 — a lower-GPI 5mm option, and Zakk’s admitted favorite platform in general. Run it with an insert and the collar, cut as short as your broadhead choice allows, and the low GPI gets you decent FOC without much effort. Max Stealth or the factory-fletched Hybrid in a three-fletch, two degree right helical. For the head, he’d move off the 2.0 to a SEVR 1.75, maybe the Hybrid, or the Evolution Hyde — one of the most aerodynamic broadheads in the 2025 study, which surprised people given its design. Mostly stock components, not overthought, and you end up with a light arrow with a very flat trajectory and limited wind drift.

Better

Same 5.0, cut short, but add 50 to 75 grains internally with Easton’s HIT insert system or a FACT weight system to push FOC up. DCA Super Sabres on the back, fletched two degree helical. Pair it with a SEVR 1.5 or 1.75 and you get a well-steered broadhead, flat trajectory, and a lot of FOC. The Grim Reaper Fatal Steel is an equally strong pairing here — it grouped with field tips at 290 fps in 2026. If you’re shooting north of 310 fps, the SEVR 1.5 is the pick; it dominated at 325-plus.

Best

Move to a 4mm shaft for the 10% drag reduction, better penetration from less surface area, and the flattest, most wind-resistant build of the three — Zakk believes it’s what Yates runs out West. A 4mm Axis with the 55 grain outsert works stock, and you can step that up to 75 or even 100 grains depending on how heavy you want to run; a titanium version is worth it if you can swing it. Target FOC around 14 to 18%, which keeps the arrow from getting heavy while still steering well and carrying good kinetic energy on impact. Flex Fletch FFP 360X on the back — the stiffer material — in a three-fletch, two degree helical, with a SEVR 1.5/1.75 or the Fatal Steel up front. The 360X outperformed the standard 360 at 325 fps in the 2026 high-speed data, at the same quiet profile.

The logic of the best tier is that every choice attacks the same problem from a different angle: narrow shaft for drag, short cut for stiffer spine, stiffer vane material for the speed, and the most aerodynamically accurate mechanicals in the study. The one real cost is money — 4mm components are more expensive.

40:29Build Three: The Fixed-Blade Purist

Committed to a fixed blade regardless of the flight data, with penetration as the primary goal. The aim here is the most accurate fixed-blade build possible, which means more overall weight behind the head and more FOC.

Good

The Easton Axis 5mm again — higher GPI, very durable, hard-hitting, and a natural fit with a fixed blade. Basic insert and collar puts you around 11 to 13% FOC depending on how short you cut it. Stock fletching, the Hybrid or Max Stealth, three-fletch two degree helical, which steers fairly well. For the head, the Evolution Jekyll: if you’re going fixed blade, start with the head that grouped best in the study. Everything else in 2025 was inches behind it, and accuracy is what drives recovery.

Better

Step to the FMJ Max — not for weight or GPI, which are similar, but for the carbon-and-aluminum blend that pushes through on impact. Cut it as short as you can and add weight internally to raise FOC. On the back, because you’re running a fixed blade, go to the AAE Talon in a three-fletch two degree helical — the data-backed vane for this job, with 6.3 inches less drift than average across two confirmed years. Jekyll or Toulou up front.

All Nine Builds, Side by Side

Scenario Tier Shaft Vane Broadhead
Whitetail timber
≤35–40 yds, quiet + penetration
Good Easton Axis 5mm, cut short, stock insert + collar (11–13% FOC) AAE Max Stealth or factory Hybrid, 3-fletch 2° right helical SEVR 2.0
Whitetail timber Better Easton FMJ Max, cut short, 50–75 gr internal via HIT insert AAE Max Stealth / Hybrid, 3-fletch 2° right helical SEVR 2.0
Whitetail timber Better still Easton FMJ Max, cut short, internal weight Flex Fletch FFP 300, 4-fletch 2° right helical SEVR 2.0
Western
40–80+ yds, flat + range forgiveness
Good Easton 5.0, cut short, insert + collar AAE Max Stealth or factory Hybrid, 3-fletch 2° right helical SEVR 1.75 / Hybrid, or Evolution Hyde
Western Better Easton 5.0, cut short, 50–75 gr internal (HIT / FACT weight) DCA Super Sabre, 2° helical SEVR 1.5 / 1.75, or Grim Reaper Fatal Steel
Western Best 4mm Axis, 55 gr outsert (up to 75–100 gr), 14–18% FOC Flex Fletch FFP 360X, 3-fletch 2° helical SEVR 1.5 / 1.75, or Grim Reaper Fatal Steel
Fixed-blade purist
penetration first
Good Easton Axis 5mm, basic insert + collar (11–13% FOC) Stock Hybrid / Max Stealth, 3-fletch 2° helical Evolution Jekyll
Fixed-blade purist Better Easton FMJ Max, cut short, internal front weight AAE Talon, 3-fletch 2° helical Evolution Jekyll or Toulou
Zakk’s 2026 build
whitetail-led, some longer shots
Personal Easton 5.0, 300 spine, ~27.5″, 50–75 gr internal (HIT) + collar, 100 gr point, 440–465 gr total AAE Max Stealth or DCA Super Sabre (undecided) SEVR 1.75 Hybrid

Zakk’s caveat on all of it: these are examples he put together from the study, not the only correct builds. There are effectively infinite options in arrow building, and he’s not claiming his interpretation is the last word.

44:53What Zakk Is Actually Building for 2026

He runs himself through his own framework out loud. This year is whitetail-led — North Carolina, Kentucky, and potentially Texas — so he wants an arrow optimized for that, with enough range forgiveness to handle a longer shot if Texas happens.

Where he is now: an FMJ Max at 11.9% FOC and 465 grains total, out of a PSE Mach 33 with the EC2 cam at roughly 76 to 80 pounds and a 28.5″ draw. He’s blunt that there’s nothing special about the arrow — it’s simple, and it’s a fantastic whitetail arrow. He killed whitetails with it last season and recovered everything inside 50 yards shooting a SEVR 1.75 Hybrid. (He also shot some of last year’s deer with the 5.0.)

Where he’s going: back to the Easton 5.0 in a 300 spine, cut to about 27.5 inches, with 50 to 75 grains added internally using Easton’s HIT system, the collar on, and a 100 grain point — he’d ideally go 125 for the broadhead material, but he’s stuck with 100 forever and isn’t changing now. Dropping from the FMJ Max’s GPI to the 5.0’s lower GPI is what does the work: FOC climbs significantly while total weight stays in his target window of 440 to 465 grains, and he’d like to be shooting in the 290s this year. Per the study, a faster bow doesn’t hurt broadhead accuracy, so if he can find speed he’ll take it.

The one open question is the vane. He’s torn between the AAE Max Stealth he’s always run and the DCA Super Sabre the data likes, and says he’ll probably test both himself — which is the right instinct even when the data already exists. Either one gives him the lift recovery he needs, which loops back to his honest answer on question three.

“Not saying I’m going to be that much better, but there’s room for optimization and improving on what I’m doing. I get a little bit more range forgiveness, better penetration, better steering. Why not do it?” — Zakk Plocica

48:26Six Rules for Every Arrow You Ever Build

Scenario-independent, tier-independent, budget-independent. These apply to every build in this episode and every build you make after it.

1. Square both ends of the shaft

The 2026 team ran a before-and-after during the study — same machine, same bow, same arrows, with the only change being squared nock ends between sessions. The groups tightened up dramatically. A squaring tool is cheap and it costs you a couple of minutes to pull the nocks and square the front and rear. There’s no real excuse to skip it.

2. Tune the bow before you do anything else

Center shot, cam timing, everything level. A tuned bow is the precondition for all of this, not a step you get to after you’ve picked parts.

3. Retune after every meaningful change

Change point weight, cut the arrow shorter, swap the broadhead — retune. Any of those changes affect the tune. The 2026 study retuned after every single arrow category in the 34-arrow matrix, which tells you how optional it isn’t.

4. Match vane material to the speed of your bow

Under 310 fps, a standard, slightly softer material like the Flex Fletch 360 is fine. Over 310, go stiffer — the 360X outperformed the standard 360 at 325 fps in the 2026 high-speed data, at the same quiet profile. Know your speed and pick accordingly.

5. Build the system, not the parts

The one Zakk thinks people miss most. In the 2026 combo noise testing, pairing a loud broadhead with a quiet vane versus a loud vane made a difference of only 1.6 decibels — the broadhead dominated the result.

“A quiet vane paired with a loud broadhead is not a quiet arrow.” — Zakk Plocica

6. Go stiffer than the spine chart says — within reason

On modern bows with shimmable cams, the 2026 study tuned every spine from 200 to 340, and stiffer performed better every time, with no reversal in the tested range. But the study cautions against going excessively stiff, because mass goes up and speed and trajectory forgiveness come down. Jumping from a 340 to a 150 doesn’t make sense — you’d add so much weight that you’d lose the flat trajectory you were building for. Everything stays relative to your draw length, draw weight, and total point weight. There’s room to play; there isn’t room to go to an extreme.

The Bottom Line

The framework is the takeaway, not the parts list. Answer four questions honestly — what and how far you hunt, mechanical or fixed blade, how you shoot under pressure, and how much noise matters where you sit. Then make three decisions in order: broadhead, vane, shaft and FOC. The builds in this episode are Zakk’s interpretation of two years of data applied to three common situations, and he says so directly — they’re options in a world of infinite options, not verdicts.

If you take one thing into the shop this week, make it the boring one: tune the bow, square your shafts, and retune after every change. No component on this page will outperform a mistuned bow.

Gear & Resources Mentioned

Shop This Episode

  • Custom Arrow Builds
  • Arrow Vanes
  • Mechanical / Expandable Broadheads
  • Fixed Blade Broadheads
  • Easton Axis 5mm, FMJ Max, 5.0 and 4mm Axis shafts
  • Easton HIT insert system
  • AAE Max Stealth, Hybrid, Hybrid HP and Talon vanes
  • DCA Super Sabre and TAC Driver 2.25 vanes
  • Flex Fletch FFP 300, FFP 360, 360X and Silent Night 2″
  • SEVR 1.5, 1.5 Hybrid, 1.75 Hybrid and 2.0
  • Grim Reaper Fatal Steel and Micro Hades
  • Evolution Jekyll and Hyde
  • Toulou, Iron Will Solid, Slick Trick Standard four-blade
  • Thorn Rift 2.2 and Beast Titanium
Get any of these at extremeoutfitters.com — use code ARCHERYPROJECT for 10% off. Arrows sold individually so you can test before committing to a dozen, free cut and glue on every shaft, and the new custom arrow builder is live for Victory with Easton coming shortly.

Zakk’s plug for the Precision Cut Archery plots is worth repeating: you can hover any data point, click it, and see the actual photo of that arrow’s group from the study. It’s free, and he calls it genuinely impressive. Both study teams put an enormous amount of work into giving bowhunters real data — go use it.

Links

Enjoyed this episode? Leave a review — it’s the single biggest thing that helps new listeners find the show.

Rate on Apple Podcasts

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *